Pallet_Racking_-_Selective_S.jpg  Selective_racking94.JPG

 Selective_racking185.JPG

Selective_racking182.JPG

Longspan_shelving_small32.JPG

Longspan Shelving

Longspan_Racking2_S.jpg

Garage Shelving

Longspan_Racking3_S.jpg

Warehouse Shelving

Garage_shelving_small27.JPG

 

LD_Cantilever_small15.JPG

Light Duty Cantilever

HD_Cantilever_small23.JPG

Heavy Duty Cantilever

LD_Cantilever_small28.JPG

HD_Cantilever_small17.JPG

 

RS_Mezzanine_small18.JPG

Rack Supported Mezzanines

S_Mezzanine_small18.JPG

Structural Mezzanines

RS_Mezzanine_small224.JPG

S_Mezzanine_small50.JPG

 

 Workbenches_small16.JPG  Workbenches_small48.JPG Workbenches_small56.JPG Workbenches_small17.JPG

Cable_rack_small18.JPG

Cable Racks

Shelving_with_bins_small7.JPG

Shelving with bins

Pigeon_Hole_small1.JPG

Pigeon Hole racks

Clothes_rack_small4.JPG

Clothes Hanging Racks

 

SPAR representatives have the expertise to carry out visual audits of your pallet racking system and advise on its suitability with respect to current OH & S standards and Racking standards. This service call out and audit is charged which will be accompanied by a detailed site report on the state of the racking or Floors and our recommendations in the form of critical and non-critical issues relevant to your system. If the recommendations are met we are able to even install Load and Maintainence signs for the installation.

What usually is involved when inspecting a pallet Rack for visible damage? 

We would like to caution here that racks are structurally loaded components of steel and such should be professsionally checked by qualified or industry personnel. If your system is fairly new or there has been an minor accident you can check the system for visible  damage as explained below and call us for a thorough check if you suspect more.

Are uprights damaged?
If the upright shows significant damage, or is twisted or contains splits or cracks, then replace it or splice a new section in. If the upright is damaged and is to be replaced, ensure the footplate is also replaced as it will also have sustained damage.

Are base plates damaged? Are they secured to the floor using the nominated number of dynabolts?


Are splices in good condition?
Check the condition of any splices. Ensure that they are in accordance with manufacturers technical specification.

Is the racking vertical? is it Out of Plumb?
Out of plumb racking is usually due to incorrect installation. Contact the manufacturer or installer.

Are racking braces damaged?
Replace bent horizontal or diagonal braces. For bracing, the member deviation from a 1 m long straight edge in either plane should not exceed 10 mm.

Are floor fixings installed?
Check that floor fixings are installed and are not damaged. Replace as required. If the floor fixing has been damaged, it is likely that the footplate will have also received damage and may need replacing.

Are rack load & maintainence signs posted?

Check that the bays conform to the MLL signs provided by the designer / installer, and that the racks have not been altered.

Are beams overloaded?

A large amount of beam deflection indicates overloading of the racking (the maximum deflection of a the beam should not exceed 1/200 of the box sections length). Where two beams connect at an upright, the beam connectors should remain reasonably parallel. If racking is overloaded or has occurred previously, the beam connectors will form a `V'. This is a quick and easy guide.

Are beams damaged?

Check for obvious signs of beams being hit by a pallet or forklift. Damaged beams should be replaced. 

Are beam connectors or safety clips missing?

Examine beams for damage and replace missing clips immediately. If clips are regularly being dislodged, contact the manufacturer or installer to determine why they are being dislodged and implement corrective action.

Has a beam popped out of its upright?

Check that beams have not popped out of the upright and are suspended on one end connector only.

Are welds damaged?

If a beam has been hit and may only show minor damage, ensure welds are checked by a competent person for cracking.


If the answer to any of the questions above is a yes please have a specialist at SPAR look at the rack damage for a professional opinion for a small nominal fee if you dont go ahead with the minimal critical suggestions. 

 

 

Powered by liveSite